With pinball making a substantial resurgence across the nation, Gentle Giant wants to make certain that these classic, gorgeous makers stay damage-free while being transferred. Oh, and we desire the people moving them to be safe, too.
At first look, pinball makers can appear intimidating to move since of their size, weight, and fragility. Fortunately, our proficient Giants have a few tricks up their sleeves to guarantee your pinball is moved with ease.
Folding Down the Headbox
The bulk of modern pinballs (made in the last 20 years or two) have a hinge system which permits the headbox to be folded down. Early pinball machines had their headboxes bolted on, using either 2 or 4 bolts. All Electro-Mechanical pinballs use this system, together with the early Strong State makers.
Later devices have hinges and utilize a locking system to keep the headbox upright. There may also be two bolts inside as included security, in case the latch is broken or unintentionally un-latched.
For Electro-Mechanical pinball makers, you require to remove the headbox rear access panel to get to the bolts and plugs within. Usually this panel has a lock on it to keep it in place, however gradually the secret may have been lost. On a regular basis, there is a screw keeping this panel in location.
Once inside, eliminate the bolts and disconnect the big connectors that have wiring going down into the device. You might wish to label these ports to put them back in the best area, however they should be different sizes, making it tough to plug back improperly.
You can now get rid of the headbox completely, or fold the headbox down onto the playfield glass. Make sure you use some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in location.
Early Solid State Pinballs
For early Solid State Pinballs, you will have to eliminate the back glass. There is a lock situated on the headbox in among three locations: the left-hand side at the top, right-hand side on top or on top of the headbox in the center.
Once unlocked, eliminate the back glass by raising it up utilizing the lift channel (at the bottom of the glass), and then pull it out from the bottom.
Open up the back box light panel by raising the latch located on either the left-hand side or right-hand side. The panel can now swing out towards you, and provide you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs need you to raise up the light panel in order to swing it open.
Now that you are within, you can remove the bolts, and any plugs that have wires going down into the device. You might desire to identify these plugs to put them back in the ideal area. You may not need to remove the plugs, as the electrical wiring must be long enough to permit the headbox to be folded down.
At this moment, you can secure the lamp panel and replace the back glass.
Modern Solid State Pinballs
For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system located at the back of the headbox. Using the provided secret, turn the lock 90 ° counter-clockwise.
For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the maker. This is a simple setup and requires no tools.
If you can now fold down the head box onto the cabinet, you're done. Ensure you utilize some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
If you can not fold the head box down, then you have to this page enter. There is a lock located at the top of the back glass in the. Use the provided secret to unlock, and eliminate the back glass by raising it up from the bottom, then pulling it out from the bottom.
Next, you will require to get rid of the display panel. You can do this by lifting it up and out. And finally, open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).
Get rid of the 2 bolts, put the back box back together, and fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it Homepage will likewise assist keep the back glass in place.
Removing the Legs.
Pinball Machine legs are held in place by eight bolts. They will be either 5/8 inch or 9/16 inch heads. The modern pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be removed, and the legs will come off.
But these captive nuts and threaded plates can be damaged, and the use of extra nuts may have been required. If this holds true, you will have to open the front door of the pinball, slide out the playfield glass, and raise the playfield.
With the front door (coin door) open, move the lock down bar lock throughout and get rid of the lock down bar. Then move out the playfield glass, and put in a safe location. Next, raise up the playfield by positioning your hand where the ball drains pipes, and raise the playfield up.
You must now have access to any nuts that might have been utilized. When any nuts have been eliminated, replace the playfield glass and lock down bar, and lock the front door.
Make sure to mark or remember which legs are for the front and back, as they will be adjusted differently to suit.
Loading the Pinball.
You are now ready to carry your pinball maker. Prior to you fill it, make certain you get rid of the pinballs so they do not bounce around throughout transport.
It might be much easier to get rid of the legs simply prior to packing the device if you are moving the pinball utilizing a van or SUV. Grab a buddy to have and help one of you supporting the pinball, while the other gets rid of the front legs. Move the maker in, then eliminate the back legs. It is much simpler to pack the device front first.
Ensure you strap the pinball in, as you do not want it moving if you have to stop suddenly!
For Electro-Mechanical pinball machines, you require to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a separate amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs utilize a fluorescent tube for the back glass lighting).
If you are moving the pinball utilizing a van or SUV, it may be easier to remove the legs simply prior to filling the maker. Get a buddy to have and help one of you supporting the pinball, while the other gets rid of the front legs.